oil sump
英 [ɔɪl sʌmp]
美 [ɔɪl sʌmp]
n. 油底壳
双语例句
- The Application of Perforation Plate in Reducing Oil Sump Noise of Some 6-cylinder Diesel Engine
穿孔板在降低某6缸柴油机油底壳噪声中的应用 - The lower portion of the disc is submerged within an oil sump.
圆盘下部浸在油池中。 - Residual oil can be drained via valve at the rear of gear reducer and oil drain valve in thrust bearing oil sump.
残油的排放可由减速机尾部的阀门和推力轴承油池的放油阀门来进行。 - Introduced to plan an oil sump and sewer in the tanks and to design a sewerage system and recovery system of oils in the bulking area.
介绍了设置集油坑排污管及库区沟网排水回收油脂系统的原理、方法、效果。 - Improved filtrating and purifying arrangement for LO and FO integral lubricating oil sump
润滑油及燃油用改进型过滤和净化装置 - It may also rub a hole in the soft aluminum timing cover, resulting in engine coolant being forced into the oil sump and ultimately destroying the engine.
它也可能摩擦中的一个漏洞软铝时机覆盖，导致发动机冷却液被强迫进入油底壳，并最终摧毁了引擎。 - Sea floor fueling station integral lubricating oil sump
水下加油站，海底加油站内装式润滑油油底壳 - Since the gear reducer is working with load, attention shall be paid to the temperature increase of axial cone bearing and sliding thrust bearing oil sump.
因为减速机此时已经是带负荷运转，所以应特别注意输入轴锥轴承的温升和滑动推力轴承油池的温升有无异常现象等。 - The bottom of the block is covered with an oil pan or oil sump.
缸体的底部有一个油盘或油底壳。 - Structure Improvement of Oil Sump Based on Structural Sensitivity Analysis
基于结构刚度灵敏度分析的油底壳结构改进 - The reducer housing design allows oil from all bearing cavities to be drained through the sump during routine maintenance.
在检修时，减速箱的设计允许润滑油从所有轴承空间排出，进入机油箱。 - By means of analysis on reasons of pressure fluctuation in benzol separator and unstable light oil quality, the measures of stabilizing level at the sump of benzol separator and of improving pipe still structure etc are taken, the ideal effect has been achieved.
通过对两苯塔塔压波动和轻苯质量不稳定原因的分析，采取了稳定塔底液位和改进管式炉结构等措施，取得了理想的效果。 - The radiated noise of the oil sump of a diesel engine was studied by experimental modal expansion technique.
采用了振动实验数据的模态扩展技术研究油底壳的辐射噪声。 - In consideration of the velocity distribution of liquid stream and the distribution of grain diameter between plates, a method of calculating oil leaching rate has been offered. It can be used to design and calculate the oil proof sump with tilted plate.
对于斜板隔油池，考虑到板间液流的速度分布和油滴的粒径分布，提出一个油滴脱除率的计算方法，可用于斜板隔油池的设计计算。 - Important Points on Design and the Assembly of Welding Jig for Oil Drain Plug Seat in Oil Sump
油底壳放油塞座焊接夹具设计和装配要点 - Research and an Improved Program for 390 Model Diesel Engine Oil Sump Fracture
390型柴油机油底壳裂纹的研究与改进方案 - The squeeze model assumes that the damping force is proportional to the oil viscosity and to the extension of the oil film in the plane of curvature of the teeth, which may depend on the lubrication conditions ( dry sump, splash, bath).
该挤压模型假定阻尼力与油粘度和轮齿曲面油膜的延展有关，而这种延展又取决于润滑条件（干聚油坑，飞溅，浸浴）。 - Mist prevention and control for thrust bearing oil sump of large hydroelectric generating set
大型水力发电机组推力油槽油雾防治研究 - Analysis on the Steel Sheet Lamellar Cracking for Oil Sump of Diesel Engine
柴油机油底壳薄钢板层状开裂分析 - Finite element methods of oil sump sheet metal stamping process
油底壳冲压成形有限元分析 - Calculation of Oil Leaching Rate for Oil Proof Sump with Tilted Plate
斜板隔油池油滴脱除率的计算 - The study was taken an oil sump as an example to analyze crack defect of permanent mold aluminum casting with thin thickness, deep cavity and large plane, and two causes, thermal stress and shrinkage stress during casting solidification.
以油底壳为例，分析了壁薄、深型腔、大平面铝合金金属型重力铸件，产生裂纹缺陷的原因，确定是合金凝固时期的热应力和收缩应力所致。 - Based on the controlling methods of sound absorption, sound insulation and damp, we take rational use of some materials to control the radiating noise from the engine room, engine cover, and oil sump tank and so on.
综合运用吸声、隔声、阻尼等噪声控制策略，合理选用材料分别对发动机舱、发动机罩、油底壳等处进行降噪处理，以达到降低发动机辐射噪声的目的。